How Close Can a Crane Work to Power Lines?

Crane Work to Power Lines

Under OSHA’s construction crane rules, a crane (including its boom, load line, load, and rigging) must stay at least 20 feet from an energized power line of up to 350 kV, unless the exact voltage is confirmed and the lower Table A distance is used instead. Table A sets minimum distances by voltage, from 10 feet for lines up to 50 kV, up to 45 feet for lines over 750 to 1,000 kV. The other option is to have the utility de-energize and ground the line before work begins.

Overhead power lines are one of the most serious hazards on any crane job. Electricity can arc across a gap without direct contact, so distance is the first line of defense. This guide explains the clearance rules in plain language, the steps required when work gets close to a line, and what to do in an emergency.

This article is general information, not legal or engineering advice. Always confirm requirements with the line owner, the current OSHA text, and your site’s lift plan.

The OSHA Rules That Apply

What it is: OSHA’s Cranes and Derricks in Construction standard (29 CFR 1926 Subpart CC) sets the power line safety requirements for cranes on construction sites. The key sections are 1926.1407 (assembly and disassembly) and 1926.1408 (equipment operations) for lines up to 350 kV.

Before work begins, the employer must assess the work zone to identify any power lines and decide whether any part of the crane, load line, or load could get closer than the minimum distance. If it could, the employer must choose one of three options.

Your Three Options When Working Near Power Lines

  1. De-energize and ground the line. The utility owner or operator confirms the line is shut off and visibly grounded at the work site.
  2. Maintain a 20-foot clearance. No part of the crane, load line, or load (including rigging and lifting accessories) may get closer than 20 feet to the line, using required prevention measures.
  3. Use the Table A clearance. If the line’s voltage is known, the minimum distance for that voltage may be used instead of 20 feet.

Table A: Minimum Clearance Distances by Voltage

Line voltage (nominal, kV)Minimum clearance distance
Up to 5010 feet
Over 50 to 20015 feet
Over 200 to 35020 feet
Over 350 to 50025 feet
Over 500 to 75035 feet
Over 750 to 1,00045 feet

Key points about the table:

  • The distance applies to every part of the crane, load line, and load, not just the boom tip, and it includes rigging and lifting accessories.
  • The line’s voltage should be confirmed with the utility owner or operator. If it has not been confirmed, the 20-foot rule is the safe default for lines up to 350 kV.
  • A common example: a typical neighborhood or commercial distribution line often falls in the “up to 50 kV” band, but never assume. Always verify the actual voltage.
  • Above 350 kV, the rules shift, and where the exact voltage is unknown for lines over 350 kV, the minimum distance is 50 feet.

Safety Measures Required Near the Line

When a crane could come within the required distance, OSHA requires planning and added protection. Measures typically include:

  • A planning meeting with the operator, riggers, and other workers involved in the lift
  • A dedicated spotter who watches the clearance and communicates with the operator
  • Proximity alarms, range-limiting devices, or range control warning devices that alert the operator or limit boom movement
  • Insulating links or devices where applicable
  • Clearly marked work zones and, where needed, non-conductive tag lines

The spotter and the operator should be trained for these duties, and everyone on site should know where the lines are before the first pick. Good planning also helps avoid other common rigging mistakes that can send a load off course.

Traveling With a Crane Near Power Lines

Moving a crane with the boom lowered, without a load, falls under a separate set of distances (Table T in the standard). These distances are shorter, but they depend on voltage, and they still require attention to ground conditions, boom position, and sway. Never assume a lowered boom is automatically safe.

What Happens If a Crane Touches a Power Line?

Contact with an energized line is an emergency. General guidance:

  • Stay in the cab and keep the crane away from the line if it is safe to move, and warn others to stay back.
  • Do not touch the crane or the load, and keep everyone away from the ground around it, since electricity can travel through the soil.
  • Call 911 and the utility immediately, and wait for the utility to confirm the line is de-energized before anyone approaches.
  • Only if there is fire or another immediate danger, jump clear of the crane without touching it and the ground at the same time, and move away with your feet together in small shuffling steps.

Training and a clear emergency plan make a real difference, which is why crews that follow strong crane safety practices review these steps before work begins.

Why It Matters for Utility and Construction Projects

Many crane jobs involve poles, substations, and service lines, including utility installation and maintenance lifts. Because state rules and local utility requirements may be stricter than the federal minimum, it is important to check with the line owner and local authorities early in planning. You can also review OSHA’s cranes and derricks guidance and learn about operator qualifications through NCCCO.

Frequently Asked Questions

How close can a crane get to power lines?

Under OSHA’s rules for lines up to 350 kV, a crane must keep 20 feet of clearance, or the Table A distance for the line’s confirmed voltage (10 feet for lines up to 50 kV, 15 feet for over 50 to 200 kV, and 20 feet for over 200 to 350 kV), unless the line is de-energized and grounded.

What is the 20-foot rule for cranes?

It is the default minimum distance that no part of the crane, load line, or load may get closer than when working near energized power lines of up to 350 kV, unless the exact voltage is known and a Table A distance is used.

Do power lines have to be shut off before a crane works nearby?

Not always. The line can be de-energized and grounded by the utility, or the crew can keep the required clearance using measures such as a spotter and warning devices.

What should you do if a crane touches a power line?

Stay in the cab if possible, warn others to stay away, call 911 and the utility, and do not leave the crane unless there is fire or immediate danger, in which case jump clear without touching the crane and the ground together.

Planning a Lift Near Power Lines?

Working near overhead lines takes careful planning, the right equipment, and a crew that treats clearance as non-negotiable. Contact MHM Cranes LLC for a free quote and help planning your lift.

Scroll to Top